• Sets outside diameter (D1) of Air Intake connection at End1.

• Sets the straight connection length (L1) at End1.

• Sets offset distance between End1 connect point and side of box. Minimum offset equals radius of Air Intake.

• Sets offset distance between End1 connect point and top of box. Default offset equals radius of Air Intake.

• Sets width of base of unit.

• Sets height of the body, including control box.

• Sets height of the condenser body.

Box | Height

Box | Width

• Sets dimensions of sides of unit.

• Sets the gap between adjacent Box.

• Sets width of the center body of unit.

• Sets the straight length of inlet/outlet coils.

• Sets horizontal offset to coil inlet from the side.

• Sets vertical offset to coil inlet from the top.

• 1-back
• 2-bottom
• 3-left
• 4-right

• Puts heating/cooling coil and drain connections on one of the above sides of unit.

• 1-left
• 2-right

• Sets one of the above sides of the control box to place inlet of coil.

• 1-left
• 2-right

• Sets one of the above sides of the control box to place outlet of coil.

• Sets outside diameter of inlet/outlet coil connections.

• Sets horizontal offset to coil outlet from the side.

• Sets vertical offset to coil outlet from the top.

• 1-right
• 2-left
• 3-back

• Sets one of the above sides of the unit to place coils.

• Sets the straight length at End1.

• Sets the straight length at End2.

• 1-back
• 2-front
• 3-bottom
• 4-top

• Puts End1 connection on one of the above sides of unit.

• 1-Duct
• 2-Grille

• Sets connection 1 of control unit ducted or grilled type.

• 1-back
• 2-front
• 3-bottom

• Puts End2 connection on one of the above sides of unit.

• 1-Duct
• 2-Grille

• Sets connection 2 of control unit ducted or grilled type.

• Sets and sizes end with a flange connection.

• Sets and sizes end with a male connection.

• Sets and sizes end with a female connection.

Example: fl-2;fe-.13 creates a flange at End1 with size 2, and a female connection at End2 with an overall reduction of component's dimensions of .13

• Sets horizontal offset to cooling coil inlet from the side.

• Sets vertical offset to cooling coil inlet from the top.

• Sets horizontal offset to cooling coil outlet from the side.

• Sets vertical offset to cooling coil outlet from the top.

• 0-none
• 1-plumbing
• 2-electrical

• Sets the type of cooling coil.

The Heating Coil Type is always set opposite to that of Cooling Coil Type. Both should not be none type, at least one type is set plumbing

• Sets vertical offset to drain outlet from the bottom.

• Sets length of drain outlet.

• Sets outside diameter of drain connection.

• Sets horizontal offset to drain outlet from the side.

• Sets length for the grille connection at end 1.

• Sets height of the front body of the fitting, less than Body Height.

• Sets outside diameter of Gas Inlet.

• Sets the straight length of Gas Inlet.

• Sets offset distance between Gas Inlet connect point and side of box.

• Sets offset distance between Gas Inlet connect point and top of box.

• Sets length for the grille connection at end 2.

• Sets horizontal offset to heating coil inlet from the side.

• Sets vertical offset to heating coil inlet from the top.

• Sets horizontal offset to heating coil outlet from the side.

• Sets vertical offset to heating coil outlet from the top.

• 0-none
• 1-plumbing
• 2-electrical

• Sets the type of heating coil.

The Cooling Coil Type is always set opposite to that of Heating Coil Type. Both should not be none type, at least one type is set plumbing.

• 1- Condensing
• 2- Atmospheric

• Sets modular type. Drain properties effect when type is set to Condensing.

• Sets number of columns of radiator boxes in modular.

• Sets number of rows of radiator boxes in modular.

• Sets outside diameter of Return Outlet.

• Sets the straight length of Return Outlet.

• Sets offset distance between Return connect point and side of box.

• Sets offset distance between Return connect point and top of box.

• 1-Back
• 2-Left
• 3-Right
• 4-All

• Sets the location or surface on the unit for inlet and outlet connections.

  Side “All” sets all connections on top, except drain on back.

• Sets distance between modular boxes and service panel, allowing sufficient gap.

• Sets outside diameter of Supply Inlet.

Positive <numeric value>

• Sets the straight length of Supply Inlet.

• Sets offset distance between Supply connect point and side of box.

• Sets offset distance between Supply connect point and top of box.

• Sets tag value visible in output of drawing composition in dynamic view. Separate tag strings with a semi colon.